Search results

  1. STIMULA8

    The Batmobile_Engage Member Journal

    Don't ban em!! Lol but yes for the big plug use a long pipe on the breaker bar Sent from my iPhone using Tapatalk
  2. STIMULA8

    3 port ebcs not sure what brand? Boosting issue?

    I will still do a log of those parameters you told me to log, HolyCrapItsFast Sent from my iPhone using Tapatalk
  3. STIMULA8

    3 port ebcs not sure what brand? Boosting issue?

    Hmm okay I'll take this in mind, I just switched the hoses back to original spots like the diagram. Now its boosting fine. When I switched the hoses and went for a drive I got a lot of smoke, maybe the vac lines and the inside of the solenoid was dirty? It maybe cleaned them out and pushed out...
  4. STIMULA8

    3 port ebcs not sure what brand? Boosting issue?

    Hmm so even a post turbo (in the mid pipe) can cause this? I Did my oil feed line/AVCS line and I fixed that so no more oil leaking on my up pipe, I also changed my spark plugs. When the battery was disconnected and I was finished with all of that (about 2 hrs later) I connected it back up and...
  5. STIMULA8

    3 port ebcs not sure what brand? Boosting issue?

    Okay I'll try and get this done today. Thanks Holy! Sent from my iPhone using Tapatalk
  6. STIMULA8

    The Batmobile_Engage Member Journal

    At work we use grey to mate pans and transfer cases, I'd go with grey, it's really close to the same stuff, when my bell housing for the front diff was put on the rear half they used black, no leaks, it all works great if you make the surfaces shiny again and bead it evenly, and use your finger...
  7. STIMULA8

    The Batmobile_Engage Member Journal

    Permatex that pan after you wiz wheel with a red pad the mating surface of the transmission and the pan. Sent from my iPhone using Tapatalk
  8. STIMULA8

    3 port ebcs not sure what brand? Boosting issue?

    I have no leaks I just fixed the inlet remember? I had to take w The whole manifold off, there are no leaks anywhere. I do have a post turbo leak but that wouldn't cause the boost to hesitate. Do you think it's possible, this is long shot. My up pipe is a ceramic coated GS with EWG, the flex...
  9. STIMULA8

    3 port ebcs not sure what brand? Boosting issue?

    Okay I'll switch the hoses back to the original diagram, in the first post. That is how they were always ran. What parameters will I log Holy? Thanks for your help Sent from my iPhone using Tapatalk
  10. STIMULA8

    3 port ebcs not sure what brand? Boosting issue?

    the ebcs I have was given to me from performance auto solutions, not sure what brand it is, the fitting say eaton on them, there is no brand on the solenoid itself. It is a 3 port just like any other, and is marked ports 1, 2, and 3 Sent from my iPhone using Tapatalk
  11. STIMULA8

    3 port ebcs not sure what brand? Boosting issue?

    So I have my setup exactly like this and I'm having boost hesitation, I switched lines 1 and 3 and now it boosts amazing but now I have to watch because it can over boost. So do u think I have a bad ebcs? I'm not sure if that's the issue or not. But there's no hesitations anymore it just keeps...
  12. STIMULA8

    The Batmobile_Engage Member Journal

    Use ramps like this Sent from my iPhone using Tapatalk
  13. STIMULA8

    The Batmobile_Engage Member Journal

    For the big drain plug I wasn't under the car with the long pole [emoji106]?[emoji16] Sent from my iPhone using Tapatalk
  14. STIMULA8

    The Batmobile_Engage Member Journal

    I needed a 1/2" breaker bar 2 ft long with a 5ft long steel pole slid on it and tugged for the front big one for the front diff case, then the breaker bar was good enough for the small drain plug Sent from my iPhone using Tapatalk
  15. STIMULA8

    The Batmobile_Engage Member Journal

    No sir they are both righty tighty and lefty loosey lol Sent from my iPhone using Tapatalk
  16. STIMULA8

    The Batmobile_Engage Member Journal

    Ouch Batmobile_Engage I thought my FMIC was bad, my fins are pretty bent up, that bumper support beam must not of had any protectant over the metal? Was it polished metal or painted black when you got it? Sent from my iPhone using Tapatalk
  17. STIMULA8

    The Batmobile_Engage Member Journal

    Hell yeah man. Maybe it's a 50mm don't quote me yet lol I need to double check.. The gun Is down at my cottage about an hour from my house lol. When I get out there maybe Sunday I'll post pics of the rifle! It's pretty clean, I love it! Sent from my iPhone using Tapatalk
  18. STIMULA8

    The Batmobile_Engage Member Journal

    Great setup though! In the future one day, I'll do this. I need other things first. I need a bunch of new tools for work, they just opened a harbor freight by my house. I have to finish the car to get dyno ready by next spring. It's all small issues but I want it to be perfect for the PROTUNE...
  19. STIMULA8

    The Batmobile_Engage Member Journal

    Very nice man Sent from my iPhone using Tapatalk
  20. STIMULA8

    The Batmobile_Engage Member Journal

    It's called a skid plate people lol make them bow to it! They need to bend over to see it anyways haha [emoji122]? did u make this yourself? I like it! I wanna do a stop sign skid plate but stop signs are very rare to come by [emoji23] Sent from my iPhone using Tapatalk
Top