Search results

  1. evans609

    Brandon's 2012 ISM STI

    And that held the access port? I already have the other one ordered but if it wobbles Ill def try this one haha
  2. evans609

    Post Dyno Sheet, Mods and Tuner

    So ill start.. 2012 STi Virtual Tune (Dynojet) Air Temp: 77F Car weight: 3373 with about 320 extra pounds (Air Suspension, Hardwood trunk, 1 Occupant) Gear: 3rd 2500-redline Tires: 255/35/18 Tuned By: Corbin Johnson at Johnsontuning.com Mods: Forged Pistons Full intake...
  3. evans609

    Post Dyno Sheet, Mods and Tuner

    Hi All, I had seen something like this on another forum and havent seen it here and I much rather the community here so I said I would start one. So the reason for this thread is to post up a dyno sheet, mod and tuner for people to scan down through and compare similar mods perhaps or...
  4. evans609

    Brandon's 2012 ISM STI

    Well finished tuning last night about 3am lol but all worked good. AFRs was sick, zero to small feedback knock. Was a good night for it. Made really good numbers and consistent. But heres the numbers anyways. She made 441whp and 384wtq I know many dont like the virtual dyno but its all I...
  5. evans609

    Brandon's 2012 ISM STI

    So another quick little update; Noticed last night my driver side low beam light wasnt on so during my days off next week Ill have to take the front bumper off and have a look at the connections. If not might have to order some new low beams. Also during days off Im going to pick up some...
  6. evans609

    Brandon's 2012 ISM STI

    I dont know haha I feel confident in those numbers for it reads it as a dynojet. Corbin says the virtual tune actaully reads really accurate if you have the info filled out correctly lol
  7. evans609

    Brandon's 2012 ISM STI

    Well folks just a little update; First of all I did a little virtual dyno run and I know the virtual has a lot of factors to it that would affect it but, I found a flat road, did a log of just a 3rd gear pull from 2500rpm, checked the elevation on both sides of the flat and managed to get out...
  8. evans609

    Brandon's 2012 ISM STI

    Ok so I am getting my money back from paypal so I just went ahead and bought new fender flares and they should be here within 10 days which is not bad.
  9. evans609

    Brandon's 2012 ISM STI

    Thanks! :)
  10. evans609

    Brandon's 2012 ISM STI

    Thanks! They seem to be hahah only time will tell now lol Appreciate it :)
  11. evans609

    Brandon's 2012 ISM STI

    The other update I forgot to say is; Tuning is still ongoing but everything seems to be running great so hopefully it will be done soon then I will make some videos. second the widebody I wanted has been extremely delayed and has got me frustrated so I have got my money back and going to go...
  12. evans609

    Brandon's 2012 ISM STI

    Guess that means you like it? Hahah
  13. evans609

    Brandon's 2012 ISM STI

    Heres some pics of the final product So the other little thing was the o2 sensor replace. I didnt get to grab any pics but I will try and remember to grab some tomorrow. During tuning I threw a code. (Pic below) which all it came down to was my gas cap wasnt tightened fully.
  14. evans609

    Brandon's 2012 ISM STI

    Other little project was to paint my hella horns bronze to hopefully match my lip on my wheels or close too. So it took like a dozen little bolts on the front of the horns and disconnect the horns and bracket to make it easier to access. Hard to tell here but I used 800 grit sand paper to...
  15. evans609

    Brandon's 2012 ISM STI

    Placed them in the car to make sure cutoffs where good and just had to make some fine adjustments. Close up shot. Low beam is 6500K and high beam is 5000k Rebaked the lights and put them back together and took a flash shot to show you the red affect. Flash off
  16. evans609

    Brandon's 2012 ISM STI

    So we quickly realized that the threaded end of the projector bowl was not long enough to make it through the highbeam bowl and out the back. So we had to cut down the back of the projector. Here is the back of the projector housing before And after we cut the backs. After this...
  17. evans609

    Brandon's 2012 ISM STI

    Another update; Got my headlights done, O2 sensor replaced, horns have been painted. So this is the pics and walk through of installing projectors in the high beam. So first is removing the bumper which is pretty easy. Few push clips underneath and some inside the wheel well. Then a few...
  18. evans609

    Brandon's 2012 ISM STI

    So the plan this days off is to hopefully finish the trunk for now, I also plans to swede wrap the inside and wrap the tank and also have to mount the water filter for the water in the tank. Raise up the back suspension and lower the front to get it to match. Take some pics of driving height and...
  19. evans609

    Brandon's 2012 ISM STI

    That is all the way down. I need to adjust both front and back. Bring the back up a bit and lower the front just a bit to try and get them to look even lol
  20. evans609

    Brandon's 2012 ISM STI

    Thanks! HAHAHAH yea good ole waldo. Here is some pics. Good some adjustments left to make but this is her bagged. IGOTASTi you can def use these :) lol
Top